Monthly service plan: spread the cost over 12 months•Servicing, brakes and MOT in one plan•£5 off tyres and free puncture repairs for members•
See the plan
Engine control unit with its lid off, connected to bench equipment in the Uxbridge workshop

UNLOCKING · BENCH WORK · CLONING · RECOVERY · MAIL-IN

Bosch MG1 and MD1 ECU unlocking and repair in Uxbridge

This page is for drivers whose car won't start or runs badly after an engine ECU fault, and for garages that need a bench partner for Bosch MG1 and MD1 units. Instead of a dealer-priced new ECU, we repair, recover or clone your car's own unit at our Uxbridge workshop. You can bring the car in or post the ECU to us.

Signs you need this

  • The car cranks but won't start, and the engine ECU doesn't communicate
  • The car stopped starting after a software update or a flash that didn't finish
  • Water has reached the ECU, or it failed after a jump-start or battery fault
  • The car has had a tuning file that left it running badly or not at all
  • A dealer has quoted a new ECU plus programming
  • You've bought a used ECU and the car won't recognise it

What we do

What MG1 and MD1 are

MG1 (petrol) and MD1 (diesel) are Bosch's current engine ECU platforms. They have been fitted from roughly 2016 on VW Group, BMW, Mercedes-Benz, Stellantis, Ford and other makes, replacing the older EDC17 and MED17 units.

They run on Infineon AURIX multi-core processors: TC2xx (for example TC275, TC277, TC297 and TC298) on earlier units and TC3xx (for example TC387 and TC397) on later ones. The processor has a hardware security module and password-protected flash, and the firmware is signed. That is why corrupt or altered software can leave the car not starting.

Many variants can't be read or written through the diagnostic socket. We read them on the bench through the connector pins, and on some variants the case has to be opened.

MG1/MD1 unlocking

Before an MG1 or MD1 unit can be read, backed up or written, it has to be unlocked. We unlock the ECU on the bench, take a full backup of its original data, and only then carry out the agreed work: cloning to a donor, recovery after a failed flash, board repair, or restoring the original software. Unlocking is how we get access to the unit; it never removes emissions equipment, turns off the immobiliser or changes mileage.

Why these ECUs fail

  • A software flash that failed or was interrupted
  • Water getting into the unit
  • A jump-start or a battery fault
  • A bad tuning file

What we offer

  • MG1/MD1 unlocking on the bench, with a full backup before any work
  • ECU cloning to a donor unit: your original software and data copied to a matching replacement
  • Bricked and water-damaged ECU recovery, including component-level PCB repair
  • VAG Component Protection: online adaptation for replacement modules on Audi, VW, SEAT, Skoda, Cupra and Porsche
  • ECU mail-in service for drivers and garages anywhere in the UK

For garages

We work as an outsourced electrical department for other garages. Send us the unit or the car, and you get it back tested, with your customer's original data restored. Trade jobs follow the same quote process as drivers.

We repair and restore the vehicle's own ECU. Remapping is only offered with all emissions equipment kept working, and we never remove a DPF, EGR or AdBlue system, turn an immobiliser off or change mileage.

How it works

  1. 1Send us the ECU's Bosch part number (it is on the label) or bring the car in. We confirm the platform and how the unit has to be read before we quote.
  2. 2We check ownership: V5C logbook and photo ID with a matching name, or for trade jobs your garage details, the reg or VIN and the end customer's V5C on request.
  3. 3We unlock the ECU on the bench and take a full backup of the original data before any work starts.
  4. 4We repair, recover or clone the unit on the bench, depending on the fault.
  5. 5We test the unit and confirm the result before it is fitted or sent back. In most cases a 1:1 clone works without any extra coding.

Makes covered

  • Volkswagen
  • Audi
  • Skoda
  • Seat
  • Cupra
  • Porsche
  • BMW
  • Mini
  • Mercedes-Benz
  • Peugeot
  • Citroën
  • Vauxhall
  • Ford

Price

Price on request

Confirmed after we check the part number. No work starts until you agree the quote.

Frequently asked questions

How do I know if my car has an MG1 or MD1 ECU?

Send us the Bosch part number from the ECU label, or the reg, and we will check it. Every unit is checked by its part number before we quote, so we know the platform and how it has to be read.

What is MG1/MD1 unlocking?

MG1 and MD1 units are protected, so they have to be unlocked on the bench before they can be read or written. We unlock the unit, take a full backup of the original data, and then do the agreed repair, clone or recovery.

Can you read my ECU without taking it out of the car?

Some units can be read through the diagnostic socket, but many MG1 and MD1 variants can't. Those are read on the bench through the connector pins, and some need the case opened. We tell you which applies once we have the part number.

Will my keys still work after a clone?

Yes. The immobiliser data is stored inside the ECU, and a 1:1 clone copies it to the replacement along with the software, so the car recognises the unit and your keys. In most cases no extra coding is needed.

Do I need to send the whole car?

No. Many jobs only need the ECU, which you can post to us with our mail-in service. If the fault still needs finding, bring the car in for the initial computer diagnostic check (£120) first.

How long does it take and what does it cost?

In most cases 2 to 3 working days after we receive the unit. Pricing is on request: we confirm it after the part-number check, and no work starts until you agree the quote.

Good to know

Ownership is checked before any immobiliser or ECU security work. Drivers: V5C logbook plus photo ID with a matching name. Trade customers: garage name, contact, the reg or VIN, and the end customer's V5C on request. We repair and restore the vehicle's own ECU; we never turn an immobiliser off, remove emissions equipment or change mileage.

In this section

Related services

Related fault codes